Is it difficult to construct a deck for a hot tub? It depends on a variety of circumstances, but it's worth it if you're a homeowner who enjoys using their deck throughout the year.
-
Should I construct it myself or employ a professional?
-
Where should its location be?
-
What electrical improvements are required?
Can You Put a Hot Tub on a Deck?
Yes, a hot tub can be placed on a deck. Decks and hot tubs go well together, but can your deck hold 100 pounds per square foot? Before you begin planning your hot tub deck, you should inspect your deck's construction or, better yet, hire a professional.
How to Build a Deck for a Hot Tub
When constructing a deck for a hot tub, there are numerous crucial considerations to keep in mind. Before beginning, you should consult building authorities and/or a specialist who knows how to construct a deck for a hot tub. Decks.com also offers helpful deck plans.
Step 1: Prepare the Site
Where you intend to build a ground-level or recessed hot tub, excavate, level, and pack the dirt. In other situations, slope the ground to prevent water from accumulating beneath or around the deck. Employ an electrician to install or upgrade the necessary electrical service to power the hot tub. Professionals that understand how to reinforce a deck for a hot tub may be consulted.
Step 2: Set the Footings
Utilize batter boards to define layout lines perpendicular to the home, then use a measuring tape, line level, and plumb bob to locate the footing positions. Mark each footing point with landscape spikes, fluorescent tape, or spray paint. Utilize a post-hole digger or auger to dig to the desired depth, then place cardboard foundation forms in the holes. Elevate the forms and bring them to a uniform height. Inspect the forms, then fill them with concrete and level the top, if required. Attach brackets for post or beam connections to the footings once the concrete has hardened.
Step 3: Establish the Hot Tub Pad
In-ground and recessed hot tubs must be supported by a 3 to a 4-inch-thick concrete pad. As with the foundation sites, establish and mark the corners of the pad. To establish the finished height of the pad, consider the total height of the hot tub, the finished height of the deck, and the height of the hot tub above the deck surface. Install the pad on compacted, level ground using concrete blocks placed on sand, or construct a form and fill it with concrete.
Step 4: Attach the Ledger Board
Establish the final deck's height at the house, subtract the thickness of the decking, and draw a level line. Anchor the ledger board with lag screws or self-drilling structural screws along this line. Avoid inserting the screws in the locations where the joists will be attached. Verify that the screws penetrate sufficiently into the framework. Most likely, engineered trusses and joists will require strengthening. To install metal flashing over the ledger, it may be necessary to temporarily remove a row of siding.
Step 5: Install the Support Posts
At each footing, measure from the top of the post bracket to the top of the ledger board, and deduct the beam's height. The length of the post. Minor differences in post length are of no consequence. Just be sure to keep track of which footing belongs to which post. Install the posts into the post brackets after leveling them.
Step 6: Install the Beams
Center the beams on the posts or in the beam brackets on the footings with the assistance of an assistant. The beams must be level, in complete contact with each post or bracket, and wobble-free. After confirming that the beams are perpendicular to the ledger board, connect them to the posts with brackets or to the beam brackets at the footings.
Step 7: Attach the Deck Joists
Install the joist hangers along the drawn lines where the joists will join to the ledger board and beams. Standard joist spacing for wood decks is 16 inches on the center and 12 inches on the center for composite decks. In situations where a hot tub must be supported, the spacing may be reduced and the joists may be shortened and/or doubled. Install a structure that can accommodate access hatches up to 30 inches wide for recessed hot tubs. Utilize removable joists to make hatches sturdy enough for walking. These are joists that have been inserted into the joist hangers but are not attached.
Step 8: Install Blocking
The addition of blocking between the joists minimizes twisting. The perimeter blocking serves two purposes: strengthening the deck and supporting deck planks at the margins. This is particularly critical when framing a deck or the area surrounding a built-in hot tub. Place additional blocking where any railing posts will be installed to strengthen the connection between the two points. Stair stringers may also need to be blocked.
Step 9: Install the Railing Posts
Install the railings' support posts if the deck will contain railings. Using lag screws or self-drilling construction screws, secure each post to at least two structural components. Utilize a trigger clamp to hold the post in place while it is being fastened. Or use a cleat attached to the side of the post to maintain it at the proper height.
Step 10: Install the Deck Boards
Install the boards from left to right, staggering their lengths and ensuring that each board's end rests on a joist. Allow the ends to grow long enough that they hang over the sides. After securing all the boards, snap a chalk line and cut them to size. Maintain a consistent distance between boards. Use self-drilling and self-countersinking polymer-coated decking screws to minimize predrilling. Hidden fasteners are another viable alternative.
Step 11: Box Steps or Stairs
Box steps consist of numerous small platforms stacked to make stairs. They are an excellent choice for hot tub decks because they may serve as benches or tables. Where space is at a premium, stringer stairs may be preferable. Regardless of your option, adhere to the construction code: The height of the steps cannot exceed 7-3/4 inches and cannot fall below 4 inches. They must be uniform as well: The maximum height difference between the tallest and shortest step is 1/4 inch.
Installation Considerations
For Ground-level Hot Tubs
Consider placing the hot tub on a concrete slab so that it is near the deck's edge if your hot tub deck is or will be low to the ground. Then, you can construct deck tiers around the hot tub to facilitate entry and exit. Remember to leave space around the hot tub so that you can reach the servicing panels.
For Above-ground Hot Tubs
Building a deck that can hold a hot tub is not difficult, but it must be constructed with sufficient strength, which involves an understanding of joist spacing and footing placement. This is where the assistance of a professional builder or information from local building authorities might be useful.For Recessed Hot Tubs
If your present deck cannot hold a hot tub, you may frequently remove a piece of the deck and put the hot tub on a concrete slab or another firm substrate for the hot tub deck structure.
Turn Your Deck into a Backyard Oasis
Building a hot tub deck is difficult, but it shouldn't deter you. Take the leap! If you prepare in advance and keep the fundamentals in mind, enjoyment is certain to follow. Your major decision is whether to perform the work yourself or employ a professional. Once you have made this decision, you can begin designing your year-round hot tub deck.
